Drum Atlas
Menu

Yamaha · 1200 Series

Yamaha HS-1200 Hi-Hat Stand

  • Hardware
  • pro
  • current

The Yamaha HS-1200 is a three-leg hi-hat stand with an unusual compromise: the front two legs are single braced to leave room for a second pedal, while the rear leg is double braced and carries a retractable spike. It ships with two pull rods of different lengths.

Updated 2026-09-11Sources

A third answer to the double pedal problem

Two legs or three is usually presented as a binary. Yamaha declines it.

The HS-1200 keeps three legs — so the stand stays properly planted — but braces them differently. The two front legs are single braced, which makes them physically slimmer and frees up the floor space where a double pedal’s slave needs to sit. The rear leg is double braced and carries a retractable spike, so the load-bearing leg is the strong one and it grips the floor.

It is a genuinely clever piece of reasoning: the stability of a tripod mostly comes from the footprint, not from every leg being maximally strong, and the leg doing the real work is the one behind you.

For a player who wants a double pedal and a stand that does not shift, this is the most sensible design in the catalogue.

Two pull rods in the box

The pull rod connects the footboard to the clutch, and its length sets how high the hi-hats can sit.

Yamaha supplies two. The short one is for players using open-hand technique — playing the hats with the left hand rather than crossing over — where the cymbals sit low and out of the way of the snare. The long one is for conventional crossed-hand setups with the hats up high.

Supplying both is unusual and worth noticing. Open-hand players normally have to buy a shorter rod separately or live with a stand that will not come down far enough.

The locking clutch

The clutch is the assembly that holds the top cymbal on the pull rod, and Yamaha’s specific claim here is that it will not come loose even if you play your top cymbal very loose.

That case is the hard one. A loosely mounted top hat — deliberately slack so it sloshes and breathes — puts far more vibration through the clutch than a tightly clamped one, and ordinary clutches gradually undo themselves under it. The cymbal ends up sitting on the bottom hat halfway through the set.

If you like a loose top cymbal, this is the specification that matters on the whole stand.

Rubber and felt

The cymbal support is hard rubber with felt, and the combination is doing two jobs.

Felt under the top cymbal lets it move freely and stops metal touching metal. Hard rubber on the bottom cup supports the lower cymbal without damping it into silence — a soft rubber cup absorbs so much that the bottom hat stops contributing, which is a surprisingly common way to make hi-hats sound dead.

Both are consumables. Felt washers compress and harden over years, and replacing a set that has gone hard is one of the cheapest improvements available to a hi-hat sound.

Specifications

Specifications
AttributeValue
Hardware
TypeHi-hat stand1
LegsThree — front two single braced, rear double braced1
Rear legRetractable spike1
Height range80–92 cm1
ClutchLocking — holds with a very loose top cymbal1
Pull rods suppliedTwo — a short rod for open-hand technique and a longer one for higher setups1
Connecting rodStraight, with rubber insert1
Cymbal supportHard rubber and felt1
Rotating legsYes1
Footboard angleAdjustable1

Where to find it

Some links below are affiliate links — if you buy through one, Drum Atlas may earn a commission at no extra cost to you. Commission never affects what we list or how we describe it. Full disclosure.

Sources

Numbered footnotes in the spec table point here.

  1. 1Tier 1 · Primarymanufacturer spec

    HS-1200 Double Braced Hi-Hat Stand

    Yamaha · accessed 2026-09-11

  2. 2Tier 2 · Highretailer listing

    Yamaha HS-1200 1200 Series 3-Leg Hi Hat Stand

    Memphis Drum Shop · accessed 2026-09-11