
DW · 9000 Series
DW 9500 Hi-Hat Stand
The DW 9500 is a heavy-duty hi-hat stand built around a double eccentric cam, which changes the footboard's leverage through the stroke to speed up cymbal response. It plays from 28 to 43 inches, weighs 12.2 pounds, and is sold in two-leg (DWCP9500TB) and three-leg (DWCP9500D) versions.
Two legs or three
This is the first decision and it is not about stability.
A conventional hi-hat stand has three legs, arranged in a tripod. It is the most stable arrangement and it works perfectly until you try to put a double bass drum pedal next to it, at which point one of those legs is exactly where the slave pedal needs to be.
Two legs removes the offending one. The stand is slightly less planted and considerably easier to fit into a crowded setup — double pedal, left-foot cowbell, a second snare, anything that wants floor space on that side.
DW sells both as 9500TB and 9500D. The Tama Iron Cobra Lever Glide already in the catalogue makes the same choice available, and the Yamaha HS-1200 takes a third route: three legs, but the front two single-braced to free up room.
If you play a double pedal, start with two legs. If you do not, three legs is the more solid stand.
The double eccentric cam
A hi-hat stand converts foot travel into cymbal travel, and how directly it does that is the whole feel of the instrument.
A plain linkage is linear — an inch of footboard gives a fixed amount of cymbal movement throughout the stroke. An eccentric cam is off-centre, so the ratio changes as you travel: the cymbals move more per unit of foot travel at some point in the stroke than at others.
DW uses a double eccentric here, tuned so the footboard becomes more sensitive relative to cymbal movement. The practical effect is that small foot movements produce audible changes in how open the hats are, which is what makes fast half-open work and subtle foot pressure possible.
This is precisely the same physics as the Power Glide and Accelerator cams on the bass pedals in this catalogue. It is less discussed on hi-hats and matters just as much.
Infinitely adjustable locking spring tension
The spring returns the top cymbal, and its tension has to offset the weight of that cymbal.
That is worth stating plainly because it explains something drummers often find confusing: a heavy pair of hi-hats and a light pair want different spring settings, and a stand set up for one will feel wrong with the other. If you swap between a heavy pair and a light pair, this is the adjustment to make.
“Infinitely adjustable” means continuous rather than stepped, and “locking” means it stays where you set it — the same problem the Tama Starphonic snare strainer solves with a ratchet.
What to check on any hi-hat stand
Three things, in order of how much they will annoy you:
- Play at the hinge. Side-to-side movement at the footboard pivot makes the whole stand feel vague. Ball bearings, as here, are the fix.
- Clutch slip. A clutch that creeps drops your top cymbal onto the bottom one mid-set. A locking clutch is worth having.
- Spring creep. If the tension setting wanders, the feel changes over an evening.
The 9500 addresses all three, which is most of what you are paying for.
Specifications
| Attribute | Value |
|---|---|
| Hardware | |
| Type | Hi-hat stand2 |
| Cam | Double eccentric2 |
| Cam action | Increases footboard sensitivity relative to cymbal movement2 |
| Spring tension | Infinitely adjustable, locking2 |
| Hinge | Ball bearing2 |
| Legs | Swivel; two-leg (9500TB) or three-leg (9500D)2 |
| Clutch | Locking2 |
| Footboard | Uni-body folding2 |
| Playing height | 28–43 in2 |
| Weight | 12.2 lb2 |
Where to find it
Some links below are affiliate links — if you buy through one, Drum Atlas may earn a commission at no extra cost to you. Commission never affects what we list or how we describe it. Full disclosure.
Sources
Numbered footnotes in the spec table point here.
- 1Tier 1 · Primarymanufacturer spec
- 2Tier 2 · Highretailer listing