Drum Atlas
Menu

Parts of a Drum Kit

A five-piece drum kit is counted by drums, not cymbals: bass drum, snare drum, two rack toms and one floor tom. Cymbals — usually hi-hats, a ride and one or two crashes — are counted separately and are not part of the number. Everything else on the kit is hardware whose only job is holding those pieces in reachable positions.

Updated 2026-09-10Sources

Every drum, cymbal and stand on a standard five-piece kit — what each one is called, what it does, and where it sits.

Scroll to take it apart. Hover or focus any part to isolate it — or use the arrows on the stage. The diagram is original artwork, free to reference with a link.

Exploded view · five-piece drum kit

Exploded view
Diagram of a five-piece drum kit in playing position: bass drum, two rack toms, floor tom, snare drum, hi-hat, ride cymbal, two crash cymbals, and the stands, mount and pedal that hold them. 111012134256789
  1. Bass drumalso: kick, kick drum

    The largest drum, laid on its side and played with a foot pedal. Common sizes run 18 to 24 inches in diameter and 14 to 18 inches deep, with 22 × 16 or 22 × 18 as the modern default.

    Diameter mostly sets pitch and volume; depth mostly sets sustain and how much air it moves. A 20-inch kick is not just a quieter 22 — it speaks faster and sits differently in a room.

    Materials
    Ply wood shell, most often maple, birch or poplar
    Fails by
    Spurs slipping so the drum walks forward while you play — usually a worn rubber foot

    bass-drum

  2. Snare drum

    The drum directly between the player's knees, with wires under the bottom head. Almost always 14 inches in diameter and 5 to 6.5 inches deep.

    The loudest, most articulate voice on the kit, and the one most players change first. It has its own full anatomy page.

    Materials
    Wood or metal shell
    Fails by
    See the snare drum anatomy page — the throw-off is the usual culprit

    snare-drum

  3. Rack tomsalso: mounted toms, hanging toms

    The smaller toms mounted above the bass drum or on stands. A five-piece typically pairs 10 and 12 inch, or 12 and 13 inch.

    Tom sizing is about intervals, not absolutes. Even spacing between the toms matters more for fills than which exact sizes you picked.

    Materials
    Ply wood shell
    Fails by
    Mount hardware damping the shell — the reason suspension mounts exist

    rack-tom

  4. Floor tom

    The largest tom, standing on three legs to the player's right (or left, for a left-handed setup). Usually 14, 16 or 18 inches.

    The resonant low voice between the toms and the kick. Leg length and floor contact change its sustain noticeably — rubber feet on a hard floor ring longer than on carpet.

    Materials
    Ply wood shell, three chrome legs in bracket mounts
    Fails by
    Legs sliding down in their brackets mid-gig

    floor-tom

  5. Hi-hat

    A pair of cymbals on a stand, opened and closed by a foot pedal. Typically 14 inch, with 13 and 15 inch as the common alternatives.

    The timekeeper on most of the music you have ever heard. The bottom cymbal is usually heavier than the top — that weight mismatch is what gives a good chick sound.

    Materials
    Bronze — B20, B8 or a proprietary alloy
    Fails by
    Cracks starting at the edge; a worn clutch felt letting the top cymbal rattle

    hi-hat

  6. Ride cymbal

    The large cymbal to the player's right, usually 20 to 22 inches, played continuously rather than accented.

    The one cymbal where the bell, the bow and the edge are three genuinely different instruments. Ride choice defines a kit's character more than any crash.

    Materials
    Cast bronze, most commonly B20
    Fails by
    Keyhole wear at the mounting hole, from playing without a sleeve

    ride-cymbal

  7. Crash cymbals

    Thinner, faster cymbals used for accents, typically 16 to 18 inches. Most kits carry one or two.

    Thinner crashes open faster and decay sooner. Thickness matters more than diameter for how quickly the cymbal speaks.

    Materials
    Cast or sheet bronze
    Fails by
    Edge cracks from striking flat instead of glancing off the edge

    crash-cymbal

  8. Bass drum pedal

    The foot mechanism that drives a beater into the bass drum head. Chain, strap and direct-drive are the three families.

    The most mechanically complex thing on the kit and the part with the biggest feel difference between models. It has its own anatomy page.

    Materials
    Cast and machined steel, aluminium, nylon
    Fails by
    Stretched chains, loose hoop clamps and lost spring tension

    bass-pedal

  9. Bass drum spurs

    The two legs that angle down and forward from the bass drum to stop it rolling or walking.

    Almost always set too short. Spurs should carry real weight and dig in, otherwise the drum creeps away from the pedal during a set.

    Materials
    Chrome steel with rubber or spike feet
    Fails by
    Rubber feet wearing smooth; brackets loosening

    spur

  10. Tom mountalso: suspension mount, isolation mount

    The bracket holding a rack tom in position. Modern designs grip the tension rods rather than bolting through the shell, so the shell can vibrate freely.

    A shell-mounted tom is measurably drier than the same drum on a suspension mount. This is one of the few hardware changes that genuinely alters the sound.

    Materials
    Cast aluminium or zinc with steel arms
    Fails by
    Memory locks slipping, so the tom angle drifts between gigs

    tom-mount

  11. Cymbal stands

    Straight or boom stands carrying crashes and the ride. Double-braced legs for stability, single-braced for weight.

    The felt, sleeve and wing nut at the top matter more than the stand. Missing a plastic sleeve is how cymbals get keyholed and eventually crack.

    Materials
    Chrome steel tubing, cast fittings
    Fails by
    Stripped tilter teeth; boom arms creeping down under a heavy ride

    cymbal-stand

  12. Snare stand

    The three-legged basket that holds the snare drum at playing height and angle.

    The basket arms must grip the hoop without squeezing the drum out of round. Over-tightening a snare stand chokes the drum — a common and easily fixed complaint.

    Materials
    Chrome steel with rubber basket sleeves
    Fails by
    Perished rubber sleeves letting the drum rattle against bare metal

    snare-stand

Why it is called a five-piece

The count refers to drums only. A five-piece is bass drum, snare, two rack toms and a floor tom. Add a second floor tom and it becomes a six-piece; drop a rack tom and it is a four-piece. Cymbals never enter the count, no matter how many you own — which is why a “five-piece kit” listing might arrive with no cymbals at all, and often does.

The three standard configurations

  • Four-piece (bop or rock) — bass, snare, one rack tom, one floor tom. The jazz standard, and increasingly the touring standard for anyone who has to load in without help.
  • Five-piece (fusion) — 10 and 12 rack toms, 14 floor tom, with a 20 or 22 kick. Tighter intervals, faster fills.
  • Five-piece (rock) — 12 and 13 rack toms, 16 floor tom, 22 kick. Wider intervals, more low end.

Fusion and rock five-pieces are the same count with completely different voices. When a spec sheet lists only “5-piece,” the sizes are the information — not the number.

Setting it up so it does not fight you

Position is not decoration. Three things fix most setup complaints:

  1. Throne height first. Everything else is measured from where you sit. Thighs roughly parallel to the floor or angled slightly down.
  2. Snare and hi-hat next, because those two are played the most and should be the most comfortable. Everything else arranges around them.
  3. Angles flat, not steep. Steeply angled toms and cymbals invite rim hits and edge strikes — the two ways drummers break heads and crack cymbals.

Drums this diagram describes