Drum Atlas
Menu

DW · 9000 Series

DW 9700 Boom Cymbal Stand

  • Hardware
  • flagship
  • current

The DW DWCP9700 is a heavy-duty convertible straight/boom cymbal stand with three telescoping sections — ¾-inch upper, 1-inch middle and 1¼-inch base — and an 18-inch boom arm. It reaches 88 inches at the cymbal seat and weighs 12.3 pounds.

Updated 2026-09-11Sources

Toothless tilters, and why they matter

The tilter is the joint that sets the cymbal’s angle, and it is the part of a cymbal stand most likely to annoy you.

A toothed tilter has interlocking gear teeth. It holds firmly and it never slips, but it can only stop at the angles the teeth allow — and the angle you want is frequently between two of them. Every drummer has spent time choosing between slightly too flat and slightly too steep.

A toothless tilter uses friction instead, so it stops anywhere. The historic objection is that friction joints creep under playing, which is why DW adds Techlock: a secondary lock tightened with a drum key that clamps the joint once you have found the angle.

Infinite adjustment plus a positive lock. It is the right answer and it costs more, which is why you find it on flagship hardware and not on entry stands.

Compare Tama’s Quick-Set tilter on the Roadpro, which achieves the same thing with six friction discs, and Pearl’s Uni-Lock on the S-930. Three companies, three routes to the same conclusion: gear teeth were always a compromise.

Three sections, and what that buys

Most cymbal stands telescope twice. This one telescopes three times — ¾ inch inside 1 inch inside 1¼ inch.

The gain is range. Eighty-eight inches at the cymbal seat is very tall, and the stand still packs down small enough to case. For a drummer with a high ride or a cymbal reaching over a large kit, the third section is the difference between possible and not.

The cost is one more joint, and every joint is a potential wobble. DW’s answer is oversized tube joints and hinged memory locks at each one — which is also why the stand weighs 12.3 pounds.

Plastic tube insulators

A sleeve inside each tube, and the least glamorous feature here.

Metal tubes ring. A stand with a cymbal on it, close to a drum microphone, will pick up and re-radiate low-frequency energy from the kit — and it arrives on the recording as a faint metallic buzz that is very hard to identify after the fact.

Insulators damp the tube so it does not ring. It is a studio feature that costs nothing on stage and matters a great deal in a room with microphones near the hardware.

The weight question

Twelve pounds is a lot for one cymbal stand. A five-cymbal kit built on these is over sixty pounds of stands alone, before any drums.

That is the genuine trade, and it is the same one the DW 9300 snare stand makes. Heavy hardware stays where you put it, survives being knocked, and holds a large cymbal on a long boom without creeping. It also has to be carried.

For a touring player with a tech, it is straightforward. For a drummer loading their own car, the Tama Roadpro at 11 pounds or the single-braced Stage Master at 6.6 are worth considering — and the cymbal sounds the same on all three.

Specifications

Specifications
AttributeValue
Hardware
TypeCymbal stand — straight/boom convertible2
Upper tube0.75 in2
Middle tube1 in2
Base tube1.25 in2
Boom arm½ in diameter, 18 in long2
LegsDouble braced, with memory locks2
TilterToothless, with Techlock secondary drum-key lock2
Tube insulationBuilt-in plastic insulators to prevent rattle2
Maximum cymbal seat height88 in2
Weight12.3 lb2

Where to find it

Some links below are affiliate links — if you buy through one, Drum Atlas may earn a commission at no extra cost to you. Commission never affects what we list or how we describe it. Full disclosure.

Sources

Numbered footnotes in the spec table point here.

  1. 1Tier 1 · Primarymanufacturer spec

    9000 Series hardware

    Drum Workshop · accessed 2026-09-11

  2. 2Tier 2 · Highretailer listing

    DW DWCP9700 9000 Series Straight / Boom Cymbal Stand

    Sweetwater · accessed 2026-09-11