Drum Atlas
Menu

Hanus & Hert

Hanuš & Heřt Palisander Snare

  • Snare drum
  • custom
  • current

The Palisander snare is a Hanuš & Heřt stave drum in solid rosewood, documented at 14x5.5, built from vertical blocks of solid wood with minimal glue at the joints. It carries the workshop's own laminated wooden hoops and is finished by French polishing — shellac cut with ground pumice, built up over hundreds of thin layers.

Updated 2026-09-24Sources

Why the edge is so thin

Erik Hanuš explains the whole drum in one sentence: they cut the bearing edge as thin as the shell will allow, so the head touches as little wood as possible, and that is why the drums are so sensitive to the snare wires.

It follows from the construction. A plywood shell has laminations running crossways through it, and cutting a knife-thin edge into one risks opening a ply. A solid shell has no laminations to open, so the edge can be taken down further than a ply shell tolerates.

Less contact means less of the head’s energy absorbed by the shell at the edge and more of it travelling through the head to the wires underneath. A quiet brush stroke reaches the snares that a drum with a broad edge would swallow.

The snare bed is the other half of that, and the workshop’s position on it is explicitly a middle one — some makers cut no bed at all, some cut deeply, and Hanuš & Heřt chose in between.

Twenty-odd blocks of rosewood

A snare shell here is 20 to 24 vertical blocks, each 9 to 10mm thick, glued edge to edge around the circle.

Every block has to be cut to an angle set by the drum’s diameter, and the workshop varies that angle rather than holding it constant — the alternative, used by some builders, is a fixed 45 degrees with the block width changing instead, which Hanuš finds looks wrong across a kit of different sizes.

Get the angle wrong and the shell cracks. Rosewood is the hardest timber the shop works, which makes this drum the most demanding version of an already unforgiving process. The blanks are dried near a heat source for three or four weeks before machining, because the wood is still moving when it arrives.

Hundreds of layers of shellac

The finish is French polish, and it is the other thing this workshop is known for.

Shellac and ground pumice are worked into the wood with a pad, the pumice filling the grain while it abrades the surface flat. Then shellac thinned with spirit, then polishing oil, over and over, with days between coats and sanding throughout. Hanuš spent over two years learning it.

The result is a thin, hard, glass-flat surface that is part of the wood rather than a film sitting on it — and one that shows every flaw the maker failed to catch. On figured rosewood it is the finish that makes the timber the point of the instrument.

Wooden hoops

Wooden hoops are the workshop’s signature fitting, and they are laminated rather than cut: an outer band of veneer plies, a solid hardwood core, and more veneer inside.

The descriptions available differ on what the core is — a 2026 dealer listing says 10mm lignamon beech, the 2006 workshop feature says amaranth — which the spec table records as contested rather than resolving. Twenty years separate them, and a workshop is entitled to change its mind about a species.

What both agree on is the effect, and it is the one wood hoops are chosen for: a dense rimshot, tuning that holds, and a cross-stick with a woody click that steel cannot make.

Specifications

Specifications
AttributeValue
Shell
Shell materialSolid rosewood (palisander)1*From the Drumcenter.cz listing for this drum, which reproduces the workshop's own description. Hanuš & Heřt's site was not reachable when this record was written.
Shell constructionStave — vertical blocks of solid wood, minimal glue at the joints1*Retailer listing; the same method is described at length in the Muzikus workshop feature.
Blocks per shell20 to 24 for a snare drum, 9–10 mm thick2*From a 2006 workshop feature in Muzikus, in which Erik Hanuš describes the method; not a published spec sheet.
Bearing edgeCut as thin as the shell allows, for minimum head contact2*Erik Hanuš describes the edge and its purpose in the Muzikus feature; it is not a published figure.
FinishFrench polish — shellac with ground pumice, built up over hundreds of layers1*Both the retailer listing and the Muzikus feature describe the same process.
Bearing edge
Snare bedCut to a middle depth, between makers who omit it and those who cut it deep2*Described in the Muzikus feature.
Hardware
HoopsWood — 1.4 mm solid outer layer, 15 plies of 0.6 mm veneer, 10 mm solid hardwood core, 3–4 plies of veneer1†Also reported as The Muzikus feature describes the hoop as three zones — 15 veneer plies outside, solid amaranth blocks in the middle, three veneer plies inside.The retailer listing and the 2006 workshop feature describe the same hoop with different core species and ply counts, twenty years apart.
Origin
Made inCzech Republic2*The workshop is in Prague.
  • *Not yet checked against a published source. Where a numbered source is given, it is on record but has not been opened and confirmed. See how we source.
  • †Sources disagree on this value; both readings are given.

Sources

Numbered footnotes in the spec table point here.

  1. 1Tier 2 · Highretailer listing

    Hanuš a Heřt, Palisandr, 14 x 5,5"

    Drumcenter.cz · accessed 2026-09-24

  2. 2Tier 3 · Secondaryinterview

    V dílně u Hanuše & Heřta

    Muzikus · published 2006-04-05 · accessed 2026-09-24