Drum Atlas
Menu

DW · 9000 Series

DW 9503 Remote Cable Hi-Hat Stand

  • Hardware
  • flagship
  • current

The DW 9503 is a remote hi-hat: the footboard stays under your foot and the cymbals go wherever a cable reaches, on a low-profile housing that mounts to a cymbal stand. It ships with an 8-foot detachable cable, a ball-bearing hinge, a folding unibody footboard and DW's lateral cymbal seat. US Patent 5,267,500.

Updated 2026-09-24Sources

Separating the foot from the cymbals

A conventional hi-hat stand has one requirement that shapes every drum kit built around it: the cymbals must be directly above the pedal.

That is fine until it is not. A double pedal’s slave wants the floor the hi-hat stand occupies. An auxiliary hi-hat belongs on the right of the kit, where no foot can reach it. A pair of hats needs to sit over a floor tom, or high above the kit, or beside a percussionist’s setup.

A remote hi-hat cuts the mechanical connection into two ends joined by a cable. The footboard goes where your foot is; the cymbals go wherever the cable reaches and a clamp will hold them.

Cable quality is the whole instrument

A remote hi-hat is a Bowden cable — an inner wire sliding inside an outer sheath, the same arrangement as a bicycle brake.

Everything about how it feels comes from friction between those two parts and from how much the sheath compresses under load. A poor cable turns a crisp pedal into a vague one, with the chick arriving late and the closed position uncertain.

DW’s own framing is direct: a higher quality cable yields a better remote hat, and the current detachable linkage and low-profile housing are where the company put the work. Detachable matters practically — a cable is the wear part, and a cable you can replace is a stand you keep.

Eight feet, and the others

The standard cable is 8 feet, with 2, 4, 6 and 10-foot versions sold separately.

Length is not just reach. A longer cable has more inner wire moving inside more sheath, so friction rises and the action gets heavier. Fitting the shortest cable that reaches is the single best thing you can do for how a remote hi-hat plays — which is why DW sells five lengths rather than one long one.

The lateral cymbal seat

DW calls this a first in hi-hat design, and the problem it solves is one every drummer has met kneeling under their own kit.

Bottom cymbal angle — the slight tilt that decides how much air escapes when the hats close, and therefore how sharp the chick is — is normally set by a screw underneath the seat. On a remote hat mounted at head height on a boom arm, “underneath” may be nowhere you can reach.

A lateral seat puts the adjustment on the side, accessible from wherever the cymbals happen to be.

What is not in the box

DW lists the exclusions plainly: no 505 drop clutch, no carrying bag, no MG-1 or MG-2 clamps, and no cymbal stand.

That last one is the important one. A remote hi-hat’s cymbal end has to be clamped to something, and that something is a stand you already own or one you buy separately. The 9503 is the version of this stand stripped to the mechanism, which is why it exists alongside the fuller 9502.

Specifications

Specifications
AttributeValue
Hardware
TypeHi-hat stand — remote cable1
Cable8 ft supplied, detachable; 2, 4, 6 and 10 ft sold separately1
HousingLow profile1
HingeBall bearing1
FootboardUnibody folding, staying attached to the base casting when folded1
Cymbal seatLateral — bottom cymbal angle adjusts from the side1
PatentUS 5,267,5001
Not included505 drop clutch, carrying bag, MG-1 and MG-2 clamps, cymbal stand1

Sources

Numbered footnotes in the spec table point here.

  1. 1Tier 1 · Primarymanufacturer spec

    DW 9000 Remote Cable Hi-Hat Stand — DWCP9503

    Drum Workshop · accessed 2026-09-24