Drum Atlas
Menu

Roland · V-Drums 7

Roland TD716

  • Electronic kit
  • flagship
  • current

The TD716 is Roland's flagship rack kit: a V71 module, the PD-14DSX digital snare on a three-ply mesh head, four low-profile tom pads, digital hi-hat and ride, and an 18-inch wood-shell kick. Three of its pads sense digitally rather than through a piezo, which is where its expression comes from.

Updated 2026-09-24Sources

Three digital pads and the rest

What separates the TD716 from the rest of the V-Drums range is not the module alone, it is which pads the module is talking to. The snare, hi-hat and ride here are digital — the PD-14DSX, the VH-14D and the CY-18DR each carry their own sensing processor and connect over a USB-A digital port rather than a 1/4-inch jack.

Those are the three positions where a drummer plays across the instrument rather than simply hitting it. Where on the snare head the stick lands; how far the hi-hat is open at the moment of the stroke; whether the ride is being played on the bow, the edge or the bell. A piezo and a jack can approximate those. A pad with a processor in it reports them.

The toms and crashes run on the same analogue triggers the rest of the range uses, which is a sensible place to stop: a tom is struck, and positional sensing on one earns much less.

The snare pad is a drum

The PD-14DSX is 14 inches across on a shell 4.3 inches deep, with eight tension rods, a triple-flange hoop at acoustic rim height, and a snare throw-off and tensioner in the usual places. The head is three-ply mesh with a floating middle layer.

Rim height is the specification a drummer feels without being able to name. A cross-stick lands where the hand expects, a rimshot catches at the right angle, and the stick clears the hoop on a normal stroke. Electronic snares that sit low in a thin hoop teach a technique that does not transfer.

Low-profile toms

The PD-10X and PD-12X are shallow pads with multiple sensors under the head, placed to remove the hot spot — the centre of a single-sensor pad, where a strike reads far louder than the same strike two inches away. Four of them here, at 10 and 12 inches, arranged where rack and floor toms would be.

Roland publishes the sensing and the size for these pads without publishing what the head is made of, so this record does not say. It is the one specification on an electronic kit that cannot be read from a photograph, because coated rubber and mesh photograph identically.

Stage kit, stage footprint

The MDS-Stage 2 stand routes its cables internally and holds the kit at 1,650 by 1,500 mm, with the whole assembly at 56.3 kg. The 18-inch KD-18-BK kick is a real wood shell with the sensor on the head, so it takes a normal pedal and sits on the floor like a bass drum.

This is not a kit that folds into a corner. It is a kit that goes on a riser.

Specifications

Specifications
AttributeValue
ekit
ModuleV711
Pad surfaceThree-ply mesh on the PD-14DSX snare2Roland states the three-ply mesh head on the PD-14DSX product page. It does not publish a head material for the PD-10X and PD-12X tom pads or for the CY cymbal pads, so those are left unstated rather than read off a photograph.
Kit configurationV71 module, PD-14DSX snare, two PD-10X and two PD-12X toms, VH-14D hi-hat, two CY-16R-T crashes, CY-18DR ride, KD-18-BK kick, MDS-Stage 2 stand1
Snare padPD-14DSX, 14 in, 4.3 in shell depth, eight tension rods, digital2
Hi-hatVH-14D, 14 in digital, with open/half-open/closed/press, foot close and splash, and choke1
KickKD-18-BK, 18 in acoustic wood shell with a drumhead-mounted sensor1
Trigger inputsThree digital and fourteen analogue on the V71, with four spare AUX jacks on this configuration1
Footprint1,650 mm wide by 1,500 mm deep by 1,250 mm high; 56.3 kg assembled1

Sources

Numbered footnotes in the spec table point here.

  1. 1Tier 1 · Primarymanufacturer spec

    Roland TD716

    Roland · accessed 2026-09-24

  2. 2Tier 1 · Primarymanufacturer spec

    Roland PD-14DSX Digital Snare Pad

    Roland · accessed 2026-09-24