Drum Atlas
Menu

Yamaha · PHX

Yamaha PHX

  • Drum kit
  • flagship
  • current

PHX is Yamaha's flagship hybrid-shell kit: eleven plies at 10.3 mm, with a jatoba core wrapped in kapur and faced inside and out with North American maple. Every bearing edge is cut at 30 degrees, but the radius at the apex changes by drum — R4 on toms, R2 on floor toms, R1.5 on bass drums.

Updated 2026-09-24Sources

Three woods in a deliberate order

The PHX shell is not a blend, it is a sandwich with a stated logic. Jatoba, the hardest and heaviest of the three, sits at the centre. Kapur — also hard, also heavy — surrounds it on both sides. Maple, the softest wood in the shell, forms the inner and outer plies.1

Putting the dense material at the core and the compliant material at the faces is the opposite of the usual recipe, where the hard wood goes outside for projection. Yamaha’s stated aim was a shell that vibrates freely while still carrying a lot of mass, and the arrangement follows from that: the stiff core gives the drum its volume and its low-mid weight, while the maple faces stay free enough to move.

Eleven plies at 10.3 mm is a thick shell by any measure — roughly twice a typical thin maple kit. PHX is loud by design.

One angle, three radii

Every PHX edge is cut at 30 degrees. What changes from drum to drum is the radius where the head actually touches: R4 on rack toms, R2 on floor toms, R1.5 on bass drums.

The radius decides how much of the head rests on wood. A wider radius spreads the contact, damps the highest partials and rounds the attack, which is why the rack toms get R4. A tighter radius concentrates the contact, frees the head and sharpens the transient, which is why the bass drum gets R1.5 and sounds clearer than the toms above it.

Most makers vary the angle to get this effect and leave the radius alone. Varying the radius instead keeps the head-seating geometry consistent across the kit, which makes the drums tune as a family.

Aluminium hoops on a thick shell

Three millimetres of die-cast aluminium is rigid and light at the same time — a die-cast steel hoop of the same stiffness would weigh considerably more and damp the head noticeably. On a shell this heavy the light hoop is the counterweight: it lets the head ring where the shell will not.

Built rather than bought

PHX is specified drum by drum from Yamaha’s component list — bass drums from 18 x 14 to 24 x 18 in, floor toms from 14 to 18 in, rack toms from 8 to 16 in — with the outer ply chosen as maple or ash and the hardware in chrome or gold. The four drums listed above are one configuration from that list rather than a pack Yamaha sells as such.

Footnotes

  1. Yamaha’s PHX overview page describes the shell order and the thinking behind it. ↩

Specifications

Specifications
AttributeValue
Shell
Shell materialMaple, kapur and jatoba hybrid1
Plies111
Shell thickness10.3 mm1
Bearing edge
Bearing edge30 degrees throughout, with R4 on toms, R2 on floor toms and R1.5 on bass drums1
Hardware
Tom and floor tom hoops3.0 mm aluminium die-cast1
Tom mountY.E.S.S. II, with a maple mounting plate1
LugsHook lug with internal lug lock mechanism1
Build
Sizes shownOne configuration drawn from the listed components; PHX is specified drum by drum1

Sources

Numbered footnotes in the spec table point here.

  1. 1Tier 1 · Primarymanufacturer spec

    PHX — Specs

    Yamaha Corporation of America · accessed 2026-09-24

  2. 2Tier 1 · Primarymanufacturer spec

    PHX — Overview

    Yamaha Corporation of America · accessed 2026-09-24