---
title: "Tama Power Tower System"
brand: "Tama"
category: "Hardware"
url: "https://thedrumatlas.com/hardware/tama-power-tower-system"
updated: "2026-09-24"
reviewed: "no"
---

# Tama Power Tower System

The Tama Power Tower is a drum rack built on 38.1 mm curved and straight pipes with 40 × 20 mm square-section legs. The basic PMD1100M unit carries two curved uprights' worth of hardware; PMD900A and PMD1100A add sections. Guide lines printed on the pipes line up the clamps so tom and cymbal angles repeat.


## Specifications

| Attribute | Value | Status | Source |
|---|---|---|---|
| Type | Drum rack | verified | Tama |
| Tubing | 38.1 mm curved and straight pipe; 40 × 20 × 450 mm square pipe legs | verified | Tama |
| Basic unit | PMD1100M — 1,100 mm curved pipe, two 850 mm straight pipes, two square pipes, two cross joint brackets, two multi holders, four memory locks | verified | Tama |
| Additional units | PMD900A at 900 mm and PMD1100A at 1,100 mm | verified | Tama |
| Joints | J30TS cross joint bracket, J34T multi holder, A13S memory lock | verified | Tama |
| Alignment | Guide lines printed on horizontal and vertical pipes for repeatable clamp angles | verified | Tama |
| Feet | Rubber | verified | Tama |

## The guide lines

The most quietly useful thing on this rack, and it costs Tama a printed mark.

Set a tom on a rack and its angle is decided by how far the clamp has been rotated around the
horizontal pipe. Set the next one and it is decided by the same thing, independently. Get them
slightly different and the kit feels subtly wrong in a way that is hard to locate — one drum
presenting a different face to the stick than its neighbour.

A centre mark printed along the horizontal pipe gives every clamp the same reference. Line the
clamps up to it and the toms are parallel by construction rather than by eye. The vertical pipes
carry curved markings for the same reason.

Memory locks tell you where along a tube something sits. Guide lines tell you which way round it
is, which nothing else on a rack does.

## Square legs

The uprights are 38.1 mm round pipe; the legs are 40 × 20 mm rectangular section.

That is not a style choice. A rectangular section is much stiffer about one axis than the other,
and on a rack leg the load that matters is the rack trying to rotate forward and back — the
direction the drummer pushes it. Orienting the long dimension of the section in that plane puts
the material exactly where the bending is.

A round leg of equivalent stiffness would be heavier and larger. It also could not stop the leg
rotating in its bracket, which the flats do for free.

## Curved uprights

The 1,100 mm pipes are curved rather than straight, which does two things at once.

It moves the top of the rack inward over the kit while the feet stay out wide, so the mounting
points are where the drums are and the base is where the stability is. And it gets the vertical
sections away from the drummer's sight line and reach, which a straight post at the same height
would sit squarely in.

## Buying it in sections

The PMD1100M basic unit is the starting point. The PMD900A and PMD1100A add a section — the first
sized for the floor tom side or the left of a double bass setup, the second longer and intended
for the floor tom side, with a J30TS bracket to attach it to an existing upright.

Each additional unit arrives as a complete assembly: pipe, leg, bracket, holder and memory locks.
That is the difference between a rack you extend and a rack you have to re-engineer, and it is
why the part numbers are worth reading before buying.

## Sources

1. Power Tower System Basic Unit PMD1100M — Tama (tier 1) https://www.tama.com/usa/products/detail/pmd1100m.html
2. Power Tower System Additional Unit PMD900A — Tama (tier 1) https://www.tama.com/usa/products/detail/pmd900a.html

---
Source: https://thedrumatlas.com/hardware/tama-power-tower-system · Values marked "unverified" are editorial knowledge awaiting a source.
