---
title: "Canopus Tom Stand, Holder and Clamp System"
brand: "Canopus"
category: "Hardware"
url: "https://thedrumatlas.com/hardware/canopus-tom-stand-holder-clamp"
updated: "2026-09-24"
reviewed: "no"
---

# Canopus Tom Stand, Holder and Clamp System

Canopus's tom mounting range is a set of stands, holders and clamps sharing a 13 mm L-rod: single and double tom stands, single and double tom holders on 25.4 mm posts, a cymbal holder whose boom retracts into its own shaft, and a clamp that accepts tubes from half an inch to an inch.


## Specifications

| Attribute | Value | Status | Source |
|---|---|---|---|
| Type | Tom stands, holders and clamps | verified | Canopus |
| Clamp capacity | Accepts tubes from ½ in to 1 in diameter | verified | Canopus |
| L-rod | 13 mm on the tom holders and single tom clamp | verified | Canopus |
| Holder posts | 25.4 mm — 430 mm on the CSTH-2 single, 360 mm on the CWTH-2 double | verified | Canopus |
| Stand height | 500–870 mm | verified | Canopus |
| Cymbal holder | CCH-1 on a 19 mm by 310 mm post, boom retracting into the main shaft | verified | Canopus |
| Models | CSTS-2 and CWTS-2 stands; CSTH-2, CWTH-2 and CCH-1 holders; CSTP-1 clamp | verified | Canopus |

## The clamp that takes half an inch to an inch

One number here does more work than the rest: the clamp accepts tubes from ½ inch up to 1 inch in
diameter.

That range covers essentially every stand tube a drummer owns. A cymbal stand's upper section, a
hi-hat's column, a snare stand's middle tube, a rack bar — all fall inside it. So the clamp is not a
Canopus accessory for Canopus stands; it is a clamp for whatever is already on the stage.

For a player adding a tom, a splash or a cowbell to a kit that was not designed to carry one, that
is the whole question answered.

## Thirteen-millimetre L-rods

The L-rod is the bent bar that goes into a tom's bracket, and its diameter is the interface that
decides whether a holder fits a drum.

Canopus standardises on 13 mm across the holders and the single tom clamp, which is close to the
½-inch (12.7 mm) standard most of the industry uses. One rod size across the range means a holder
bought for a stand works on a clamp bought for a rack.

The posts differ by application: 430 mm on the single holder, 360 mm on the double, both 25.4 mm
in diameter, because a double holder sits lower and carries two drums rather than reaching high
with one.

## The retracting cymbal boom

The CCH-1 cymbal holder's boom section slides back into its own main shaft.

That is the same solution Sonor uses on the 4000 Series, Tama on the Roadpro and DW on the 9700 —
a boom that becomes a straight post rather than a boom that comes off. Nothing detaches, so
nothing is left behind, and the conversion between the two takes a moment.

On a holder rather than a full stand it matters more, because a holder is already being used in a
tight space: the point of hanging a cymbal off a clamp is usually that there was no floor for a
stand.

## Stands as well as holders

The CSTS-2 single and CWTS-2 double tom stands cover 500 to 870 mm and 500 to 800 mm respectively.

Those are floor-standing versions of the same idea, for players who mount toms off stands rather
than off the bass drum — which is the norm on a kit where the bass drum is left unpierced, and on
any kit assembled from drums that did not come with brackets.

## Sources

1. Tom Stand / Holder / Clamp — Canopus (tier 1) https://canopusdrums.com/en/product/tomstand-holder-clamp/

---
Source: https://thedrumatlas.com/hardware/canopus-tom-stand-holder-clamp · Values marked "unverified" are editorial knowledge awaiting a source.
