---
title: "Drum Atlas Glossary"
url: "https://thedrumatlas.com/glossary"
terms: 26
---

# Drum Glossary

## Ambassador (weight)

Remo's single-ply 10-mil head, and by extension the industry shorthand for a standard single-ply weight. The default batter head for snare drums and toms across most of recorded music.

## B20 bronze

An alloy of roughly 80% copper to 20% tin, used for cast cymbals. Harder to work than B8 but capable of far more complex overtones — the alloy behind most professional cymbal lines.

## B8 bronze

Roughly 92% copper to 8% tin, usually rolled from sheet rather than cast. Brighter, more uniform and cheaper to produce than B20 — the alloy of most entry-level cymbals and some deliberately bright professional lines.

## Bearing edge

The machined edge where the drum shell meets the head. Its angle and profile decide how much of the head contacts the shell, which sets sustain, overtone content and how easily the drum tunes. A 45-degree edge with a small outer back-cut is the modern standard; rounded-over edges are typical of vintage American drums.

## Butt plate (also: butt end)

The fixed anchor opposite the throw-off that holds the other end of the snare wires. It must sit exactly opposite and level with the throw-off or the wires seat crooked.

## Coated head

A drumhead sprayed with a textured white coating. Slightly warmer and less bright than a clear head of the same weight, and the only surface brushes work on.

## Cross-stick (also: rim click, side stick)

Laying the stick across the head with the butt end striking the hoop, producing a woodblock-like click. Standard for ballads and bossa nova patterns.

## Dampening gel (also: moongel)

A small adhesive gel pad placed on a drumhead to absorb overtones. Removable, repositionable and the least destructive way to control ring — preferable to tape for anything but a permanent fix.

## Die-cast hoop

A hoop cast in one piece rather than formed from sheet steel. Heavier and more rigid than a triple-flanged hoop, it focuses the drum, shortens sustain and makes rimshots crack harder.

## Emperor (weight)

Remo's two-ply 7+7-mil head, shorthand for a standard double-ply weight. More durable and more damped than a single ply, with a shorter, fatter note.

## Hammering

Striking a cymbal to shape its curvature and introduce tension. Hand hammering produces irregular patterns and more complex, less predictable overtones; machine hammering is uniform and consistent.

## Keystone badge

The keystone-shaped Ludwig badge used across much of the company's mid-century output. Badge shape and the serial number on it are usually the fastest route to placing a vintage Ludwig drum in a production window.

## Lathing

The concentric grooves cut into a cymbal's surface on a lathe, which thin and shape it. Lathed cymbals are brighter and more sustaining; unlathed (raw) areas are drier and darker.

## Mil

One thousandth of an inch, the unit drumhead film thickness is given in. A 10-mil single ply is standard for batter heads; snare-side resonant heads run 2 to 3 mil.

## Muffling (also: dampening)

Anything that shortens a drum's ring — gel pads, internal mufflers, felt strips, rings cut from old heads, or a wallet. Almost always better applied at the edge of the head than at the centre.

## Ply

One layer of wood in a laminated drum shell. Ply count and thickness together set shell stiffness: fewer, thinner plies give a lower fundamental and more resonance; more plies give a higher fundamental, more attack and more projection.

## Reinforcement ring (also: re-ring)

A band of wood glued inside the top and bottom of a thin ply shell to hold it round and provide material for the bearing edge. Common on vintage drums and on modern thin-shell designs; the ring stiffens the ends while leaving the middle of the shell free to vibrate.

## Rimshot

A stroke that strikes the head and the hoop simultaneously, producing a much louder and more cutting note. The backbone of most rock and pop backbeats.

## Segment shell

A shell built from stacked rings of wood segments, each ring rotated relative to the one below. Structurally very stable and common in boutique snare building.

## Snare bed

A shallow dip cut into the bottom bearing edge where the snare wires cross it, letting the wires seat flat against the resonant head. Beds that are too deep or too abrupt cause wire buzz that no amount of tuning will fix.

## Snare wires (also: snares)

Coiled metal wires stretched across the resonant head. Strand counts run from 12 to 42; 16 or 20 is standard. Wire tension is a tone control in its own right — loose is fat and loose, tight is crisp and short, and too tight chokes the drum.

## Stave shell

A shell built from vertical wood blocks glued edge to edge and turned round, rather than from bent plies. Stave construction gives a thicker, denser shell with a strong fundamental — the same principle as a barrel.

## Suspension mount (also: isolation mount)

A tom mount that grips the tension rods rather than bolting through the shell, letting the shell vibrate freely. One of the few hardware changes that measurably alters a drum's sustain.

## Throw-off (also: strainer)

The lever mechanism that tensions and releases the snare wires, carrying the fine adjustment for wire tension. The most-handled moving part on a snare drum and its most common failure point.

## Triple-flanged hoop

A hoop rolled from sheet steel with three bends, the most common hoop type. Available in 1.6mm, 2.0mm and 2.3mm thicknesses — thinner lets the head breathe and gives a looser rimshot.

## Wrap (also: covering)

A sheet of patterned plastic bonded around a drum shell as a finish, as opposed to lacquer or stain. Pearl, sparkle, oyster and mod patterns are all wraps, and most iconic vintage finishes are wrapped rather than painted.

---
Source: https://thedrumatlas.com/glossary
