---
title: "Parts of a Cymbal"
subject: "cast bronze cymbal"
url: "https://thedrumatlas.com/anatomy/cymbal"
updated: "2026-09-15"
---

# Parts of a Cymbal

A cymbal has three zones — bell, bow and edge — and four processes applied to them: casting, hammering, lathing and finishing. The single most important measurement is one almost nobody publishes: the taper, or how much thinner the metal gets between the bell and the edge. Weight matters more than diameter, and profile — the height of the arch — sets the pitch.

## Parts

### 1. Bell (also: cup, dome)

The raised dome at the centre, formed in the same piece of metal as the rest. Usually left unlathed or only lightly lathed.

The bell is the stiffest part of the cymbal, so it rings at a higher and much more defined pitch than the bow — that is why a bell pattern cuts through a band when a ride pattern does not. Bell size is a real design variable: a large bell gives more volume and more sustain from that pattern, a small one keeps the cymbal darker and gets out of the way.

- Materials: Same bronze as the body — B20, B8 or a proprietary alloy
- Fails by: Cracking radially from the mounting hole outward, usually from overtightened wing nuts rather than from playing

### 2. Bow (also: body, playing surface)

The curved area between the bell and the edge. This is where a ride pattern is played and where most of a cymbal's surface area is.

Where you play on the bow changes the sound more than most players expect. Near the bell the metal is thicker and stiffer, so it gives more stick and less wash; out towards the edge it is thinner and looser, so it opens up. One cymbal covers a lot of ground without being retuned, which is the whole argument for a big ride.

- Materials: Cast or sheet bronze, hammered and usually lathed
- Fails by: Keyhole wear at the mounting hole; fatigue cracks along a lathing groove

### 3. Edge (also: rim)

The outer perimeter, and the thinnest part of the cymbal.

The edge is what you hit for a crash, and it is the first thing to break, for the same reason: it is thin, it flexes most, and a glancing blow across it puts the whole force of the stroke into the least metal. Hitting a crash flat-on rather than at an angle is the single best thing a player can do for its life.

- Materials: The thinnest section of the same sheet or casting
- Fails by: Edge cracks, almost always. They start as a hairline and travel inward along the grain of the lathing

### 4. Taper (also: profile thickness)

Not a part — a measurement. How much thinner the metal becomes between the bell and the edge, and how gradually.

This is the most important thing about a cymbal and the least published. A steep taper gives a cymbal that rides cleanly near the bell and crashes easily at the edge. A shallow taper — nearly even thickness — gives a cymbal that stays controlled everywhere and takes real force to open up, which is why heavy rock rides are built that way. Two cymbals of the same diameter and the same weight can taper completely differently and sound nothing alike.
- Fails by: Nothing fails — but it is why weight alone tells you less than it seems to

### 5. Hammering

The dimples worked into the metal, by hand with a hammer or by machine on a press. Visible as irregular hollows on the surface.

Hammering puts tension into the bronze and breaks up its natural ringing, which is what makes a cymbal complex rather than a gong. Hand hammering is irregular by nature, so no two cymbals come out identical — that is the whole appeal and the whole inconsistency. Machine hammering is even, which gives a more predictable and usually brighter cymbal.

- Materials: Worked into the bronze, not added to it
- Fails by: Nothing directly, though a heavily hammered cymbal has more stress concentrations in it

### 6. Lathing (also: tonal grooves)

The concentric grooves cut by a lathe as the cymbal spins, removing metal to bring it to weight and shape.

Lathing sets the taper and leaves grooves that scatter the high frequencies. Wide, deep grooves give a drier and darker cymbal; fine, tight lathing gives a brighter and more even one. Leaving a section unlathed — a raw bell, a raw band around the bow — is one of the most common ways a maker gets a dry sound without changing the alloy.
- Fails by: A lathing groove is a stress line, and edge cracks tend to follow one

### 7. Mounting hole

The hole at the apex of the bell, usually about 11mm, that the cymbal stand passes through.

The cymbal has to be free to move here or it cannot ring. Felts above and below, and a sleeve protecting the metal from the threaded rod, are not accessories — they are part of how the instrument works. A cymbal bolted down tight is a cymbal being strangled, and it is also a cymbal about to crack.

- Materials: Bare metal; protected by a plastic or rubber sleeve on the stand
- Fails by: Keyholing — the round hole wearing into a slot — from playing on a bare threaded rod

### 8. Profile (also: arch, bow height)

The height of the curve, measured from the plane of the edge up to the top of the bell.

Profile sets pitch. A high profile makes a higher, more focused cymbal; a low or flat profile makes a lower, washier one that opens more easily. It is the reason a flat ride sounds the way it does — there is barely any arch, so there is barely any pitch, just stick.
- Fails by: A cymbal that has been played hard for years slowly flattens, and drops in pitch as it does

Four processes turn a disc of bronze into a cymbal, and they happen in this order:
**casting** or stamping, **hammering**, **lathing**, then **finishing**. Everything a
maker can change about the sound happens in one of those four steps, and the alloy —
the thing named on the box — is only the first of them.

The most useful thing to know when comparing two cymbals is that **weight tells you
more than diameter**, and **taper tells you more than weight**. A 20-inch ride at
2,400 grams and a 20-inch ride at 2,400 grams can be completely different instruments
depending on where that metal sits.

---
Source: https://thedrumatlas.com/anatomy/cymbal · Diagram artwork © Drum Atlas, free to reference with a link.
